Pallet rack basics

From traditional single-deep rack to dynamic, high-density rack systems, pallet rack helps to maximize cube space in the warehouse.

By Corinne Kator, Associate Editor -- Modern Materials Handling, 2/1/2007

Pallet rack systems are among the most basic and yet useful materials handling tools. Variations of these simple steel structures create order and maximize storage density in a warehouse, making good use of floor space and ceiling height.

Basic pallet rack consists of upright steel frames connected by horizontal steel beams. Pallets rest on the beams between the upright frames. Two frames and the corresponding beams form a bay. The number of pallet positions in a bay depends on the height of the frames and the spacing of the beams.

High-rise storage systems reach heights of 100 feet or more, but a typical rack height is 20 to 25 feet, says Gary Slater of Unarco Material Handling, president of the Rack Manufacturers Institute ( www.mhia.org/rmi).

The components of the upright frames—their steel posts and cross braces—can either be bolted together or welded together. Welded frames are more common in the United States, while bolted construction is more common in Europe.

There are also two choices for connecting frames and beams. Beams can be bolted to frames, or the two components can snap together using a slotted connection system.

Rack components can be made of structural steel or of roll-formed steel. Which type of steel is most suitable for which applications is often a point of discussion within the rack industry. The majority of rack sold in the United States, says Slater, is made of roll-formed steel. Structural steel costs about 5 to 10% more than roll-formed, according to consulting firm Gross & Associates ( www.grossassociates.com).

Several types of rack are available, from low-density systems that allow easy access to products to high-density systems that make more efficient use of space but limit access to what they store.

Low-density rack

The horizontal beams in a pallet rack system are connected to the upright frames in one of two ways: they are bolted on (right) or they employ one of a variety of boltless, snap-on connections (left).

Single-deep rack

Single-deep pallet rack, also known as selective rack, is by far the most common type of rack used in warehouses today. Because loads are stored only one pallet deep, single-deep rack provides the lowest-density storage of any pallet racking system.

Single-deep remains popular, however, because it permits unimpeded access to every pallet it stores. Additionally, single-deep rack can be used in a variety of aisle configurations, can be paired with any type of lift truck and is the least expensive style of rack. According to "Rules of Thumb," a pricing tool created by Gross & Associates, standard selective pallet rack costs approximately $50 to $70 per pallet position.

Double-deep rack

As its name implies, double-deep rack stores one pallet load behind another in a rack structure that's twice as deep as single-deep rack. While doubling storage density, this design limits access and flexibility.

To access the rear pallet in a double-deep rack system, the front pallet position must be empty. Double handling is necessary unless pallets are stored on a last-in/first-out basis. And in most cases, two pallets of the same product are stored in a slot of double-deep rack, which limits the flexibility of a warehouse's storage space.

"Rules of Thumb" lists double-deep pallet rack at $55 to $80 per pallet position. Putting away and retrieving loads in the rear position of a double-deep system requires a deep-reach lift truck.

High-density rack

Drive-in rack

Drive-in rack can be configured to store loads three, four or more deep, creating extremely dense storage. A drive-in system that stores pallets four high and five deep, for example, can hold 20 pallets in each bay.

In a drive-in system, lift trucks drive into the front of a storage bay, place a load in the desired position and then back out. To allow lift trucks into the bays, drive-in systems are designed without traditional beams placed across the bays. Instead, pallets rest on rails that run along the insides of the bays, perpendicular to the aisles.

Pallets in a drive-in racking system are stored on a last-in/first-out basis. Each bay is typically dedicated to a single product, so drive-in rack is best used in warehouses storing large quantities of the same product.

Drive-in systems severely limit access to products stored in rear positions. As a result, say experts, this type of storage is best suited for situations in which an entire bay of products would be moved at once, such as in staging products for shipping.

Standard drive-in rack costs $60 to $90 per pallet position for systems three loads deep and $50 to $80 per position for systems four or more loads deep, according to "Rules of Thumb."

Drive-through rack

Drive-through rack provides high-density storage and allows lift trucks to enter and leave the bays from either end.

In all ways but one, this design is the same as drive-in rack. The difference is drive-through rack allows lift trucks to enter the bays from either end. This considerably increases access to pallet loads, but requires an aisle on both ends of the racking system.

Drive-through rack can be loaded from one end and emptied from the other, allowing first-in/first-out product rotation.

According to "Rules of Thumb," drive-through rack costs approximately $65 to $105 per pallet position for systems three loads deep and $55 to $95 per position for systems four or more loads deep.

Dynamic storage

Gravity flow rack

Gravity flow rack combines a stationary rack structure with skatewheel or roller conveyor to create a dynamic storage system. Pallets are loaded into the back end of the rack and then travel down the slightly inclined lane of conveyor until they are retrieved from the front of the system.

Flow rack systems provide high-density storage by storing products many pallets deep. Because each layer of flow rack is typically dedicated to a single product, these systems offer less storage flexibility than selective rack but more flexibility than drive-in or drive-through rack where an entire bay is dedicated to one product.

Flow rack allows easy rotation of inventory on a first-in/first-out basis, making it a good choice for storing dated products. It can be used for picking by the piece, carton or pallet. Many rack manufacturers also offer carton flow rack that stores individual cartons rather than entire pallets.

Gross & Associates estimates pallet flow rack costs about five times as much as traditional selective rack—between $250 and $350 per pallet position for a standard system three or more pallets deep.

Push-back rack

Nested carts moving along inclined rails provide last-in/first-out storage in a push-back rack system.

Push-back rack combines a stationary rack structure with nested carts that move along inclined rails. Pallets are loaded from the front. The first pallet is placed on the top cart; when the second pallet is delivered, it pushes back the first pallet, exposing the second cart, and so on.

Push-back racking systems are usually configured two to five pallets deep. Like flow rack, they offer dense storage without requiring a lift truck to enter the racking system or requiring an entire bay be dedicated to one product. Unlike flow rack, push-back rack manages inventory on a last-in/first-out basis. Push-back rack requires less space than flow rack because rear access is not necessary.

Push-back rack costs roughly $95 to $135 per pallet position for a double-deep system and becomes more expensive as more carts are added, according to "Rules of Thumb." A push-back system storing pallets five deep costs about $175 to $200 per pallet position.

Talkback

» Submit Feedback

• I enjoy reading the articles on your web site. We are always looking for ways to improve material handling. I wanted to bring your attention to another type of racking system, Automated Racking. Not quite sure why you didn\'t even mention this in your article, \"Pallet Rack Basices, From traditional single-deep rack to dynamic, high-density rack systems, pallet rack helps to maximize cube space in the warehouse\" By Corinne Kator, Associate Editor -- Modern Materials Handling, 2/1/2007, as it is a very efficient, dynamic, high-density rack system. Retrotech is a leader in this area and I think deserves to be mentioned. RETROTECH, Inc. 610 Fishers Run ;P.O. Box 586 ;Fishers, NY 14453-0586Phone (585) 924-6333 FAX (585) 924-6334 E-Mail info@retrotech.com Web www.retrotech.com

  '>
  

  I enjoy reading the articles on your web site. We are always looking for ways to improve material handling. I wanted to bring your attention to another type of racking system, Automated Racking. Not quite sure why you didn't even mention this in your article, "Pallet Rack Basices, From traditional single-deep rack to dynamic, high-density rack systems, pallet rack helps to maximize cube space in the warehouse" By Corinne Kator, Associate Editor -- Modern Materials Handling, 2/1/2007, as it is a very efficient, dynamic, high-density rack system.
  
  Retrotech is a leader in this area and I think deserves to be mentioned.
  
  RETROTECH, Inc.
  610 Fishers Run ;P.O. Box 586 ;Fishers,
  NY 14453-0586Phone (585) 924-6333 FAX
  (585) 924-6334 E-Mail info@retrotech.com Web
  www.retrotech.com

  
  

  
  Kim Escott - 2008-17-3 11:07:00 EDT

• Terry: Thanks for a thoughtful response. With regard to the Kingway purchase, please note that the article was published several years ago. At that time, Kingway was still a standalone company. In these articles, Modern tries to give a comprehensive view of the industry leaders. Since articles are available on the Net for years, inevitably some information is going to be out of date. Thanks again for reading Modern.

  '>
  

  Terry: Thanks for a thoughtful response. With regard to the Kingway purchase, please note that the article was published several years ago. At that time, Kingway was still a standalone company. In these articles, Modern tries to give a comprehensive view of the industry leaders. Since articles are available on the Net for years, inevitably some information is going to be out of date. Thanks again for reading Modern.

  
  

  
  Bob Trebilcock - 2008-2-3 07:33:00 EST

• Why are you mixing distributors with Manufactors on your Rack list. Kingway has been part of UNARCO for almost 9 months, Load Bank is a pallet flow system manufactor, Boston Rack and TwinLoad are distributors.

  '>
  

  Why are you mixing distributors with Manufactors on your Rack list. Kingway has been part of UNARCO for almost 9 months, Load Bank is a pallet flow system manufactor, Boston Rack and TwinLoad are distributors.

  
  

  
  Terry Bligt - 2008-21-2 13:23:00 EST
» Submit Feedback

Related Content

• Topics
• Author

Focus on racks

02/28/2006

Dynamic storage

09/30/1999

Storage, Rack and Shelving Special

09/29/2009

Storage, Rack and Shelving Special

02/07/2008

How pallet loads stack up

10/31/2004

Also by this author

• Corporate Social Responsibility: Industrial and social symbiosis

• Top 20 lift truck suppliers 

• No more heavy lifting

• Web-based tool will facilitate product recalls

• Manhattan demos hi-tech command center

»MORE

Sponsored Links

• Resource Center
• Browse Categories
• Browse Companies

Featured Company

• Motorola

  

  Motorola is a global leader in providing integrated communications solutions and embedded electronic solutions. These include: Software-enhanced wireless telephone, two-way radio and messaging products and systems, as well as networking and... more

---

Most Recent Resources

• Propelling Productivity Through the Rising Demands of Material...
• Flexible Factories Need Flexible AGVs
• Special Report: 5 Strategies for Gaining Management Approval of WMS
• New Report: Nine Telltale Signs You Should Replace Your Current WMS
• The Visible Supply Chain: Ensuring End-to-End Optimization